User manual and frequently asked questions IXEO POWER QT2020M0
Smart and Powerful: The Garment Care Revolution
The Tefal IXEO Power All-in-One iron steamer station combines a High-Pressure Technology for ultimate steam power, with a Built-in three-position Smart Board, for exceptional results that help you look your best in no time. With an ergonomic upright to horizontal design associated to an ultra-light iron head, upgrade the garment care experience to a new era. Ready about 70 seconds, IXEO Power makes your ironing shirt twice faster and is the perfect solution for smooth & wrinkle-free looks every day.
• Untreated tap water: Your appliance has been designed to use untreated tap water. If your water is very hard, mix 50% untreated tap water and 50% distilled water.
• Types of water not to use: Heat concentrates the elements contained in water during evaporation. The types of water listed below may contain organic waste, mineral or chemical elements that can cause spitting, brown staining or premature wear of the appliance: - water from clothes dryers - scented or softened water - water from refrigerators, batteries, air conditioners - rain water - boiled, filtered or bottled water
In order to ensure the best performance from your iron, these types of water should not be used for ironing.
With its clean design, IXEO can easily blend into your home. Equipped with small wheels underneath its base, you can easily move it effortlessly. However, if you wish to store the product, it can be lowered to a height of 105cm. More compact, it can then easily be stored in a dressing room or closet.
Successively press the "Steam" button until you reach the desired mode.
• Normal mode: the green light is off. • Max mode: the green light flashes. • Min mode: the green light is on steady.
Boost steam:
By pressing the steam trigger 3 times briefly and successively, few sets of ultra-boost steam can be released for garments that require extra attention to remove the creases.
This operation should only be performed after the appliance has been unplugged for more than two hours. It could be unsafe to remove the calc-collector cap when the appliance is not cooled down properly. With the high pressure boiler, it helps to produce strong and consistent steam, and it is critical to only remove the calc-collector cap after the appliance is switched off for more than two hours. This allows the pressure of the boiler to decrease to a safe level for releasing the limescale / calcification.
To remove limescale from your appliance, please follow the instructions below:
Your product is not plugged in or is not switched on ==> Check that your product is properly connected to a power socket and that the switch is on "I". The water level in the tank is too low ==> Unplug the appliance and fill the tank. The pump is unprimed ==>Press and hold the steam button for a few seconds to prime the pump. The removable tank is not installed correctly ==> Check the correct positioning of the tank on the product. The product is in "Stand-by" mode ==> Press the "On-Off" button and wait until it stops flashing.
Your product is not plugged in or is not switched on ==> Check that your product is properly connected to a power socket and that the switch is on "I". The product is in "Stand-by" mode ==> Press the "On-Off" button and wait until it stops flashing.
The water tank is not installed correctly or its locking valve is not closed properly ==> Check that the valve is closed and that the tank is installed correctly on the product.
You have used descaling chemicals or additives in the water. Never add such products to the water tank. These contain organic waste or minerals that condense under the influence of heat and cause spitting, brown dripping or premature aging of your appliance.
You have used descaling chemicals or additives in the water. Never add such products to the water tank. These contain organic waste or minerals that condense under the influence of heat and cause spitting, brown dripping or premature aging of your appliance.
After following the instructions in the user manual for starting the appliance, make sure that your electrical socket is working by plugging another appliance. If it still does not work, do not try to dismantle or repair the appliance yourself, instead, take it to an approved repair centre
You have pressed the steam trigger 3 times briefly and successively which triggered the "Boost" mode. The steam is then automatically activated for a few seconds.
• After approximately one minute, and regularly while it is being used, your IXEO Power's electric pump injects water into the boiler. It makes a noise and this is quite normal. A slight drop in steam may also be noticed at the same time. • Your appliance has limescale, consult the "Descaling" section in the instructions.
