EXPRESS POWER SV8062

Choose a board that is height-adjustable to adjust it to your height. It should be steady and robust so that you can place the ironing appliance on it.
The board should be perforated to allow the steam to pass through the fibres of the fabric to soften it and make ironing easier. The ironing board cover should also be suitable to allow the flow of steam through.

To avoid damaging the soleplate, follow this advice:
• Always place your iron on its heel rest or its base (depending on model).
• Avoid ironing over abrasive items (buttons, zip fastenings, etc.).
• Never clean your iron's soleplate with abrasive or metallic pads.

Shiny marks can appear on some fabrics, especially on dark coloured fabrics. We would advise ironing dark clothes inside out and using the correct temperature.
If ironing mixed-fibre fabrics, set the temperature for the most fragile fibre.
Important: The iron takes longer to cool down than to heat up. We recommend that you start with fabrics to be ironed at a low temperature.

• Untreated tap water:
Your appliance has been designed to use untreated tap water.
If your water is very hard, mix 50% untreated tap water and 50% distilled water.

• Types of water not to use:
Heat concentrates the elements contained in water during evaporation. The types of water listed below may contain organic waste, mineral or chemical elements that can cause spitting, brown staining or premature wear of the appliance:
- water from clothes dryers
- scented or softened water
- water from refrigerators, batteries, air conditioners
- rain water
- boiled, filtered or bottled water

In order to ensure the best performance from your iron, these types of water should not be used for ironing.

The steam is more or less significant depending on the temperature setting of the iron. We advise you to use steam occasionally when the temperature is set low on the iron, otherwise drops of water could appear on your laundry.

Before cleaning, ensure that the appliance is unplugged and that the soleplate and iron rest plate are cold.
Do not use any detergents or descaling products to clean the soleplate or base unit. Never hold the iron or its base unit under tap water.

• Cleaning the base unit:
Clean the plastic parts from time to time with a soft, slightly damp cloth.

• Cleaning the scale collector:
Wait until the appliance has been switched off for at least 1 hour.
Remove the scale collector by lifting and rotating the flap a quarter turn.
Rinse the scale collector under the tap and put it back on the iron.

• Self-cleaning of the soleplate (depending on model):
When the anti-calc indicator blinks, perform the steps described in this video.

It is normal. Your iron generates a lot of steam; this steam is condensing on the board. Some waterdrops could appeared underneath the ironing board and fall on the flooring.

• You are using chemical descaling products or additives in the water. You should never put these products in the water tank. If this is the case, contact an approved service centre.
• Your washing has not been rinsed sufficiently or you are ironing a new item of clothing before washing it. Ensure that you have rinsed your clothes thoroughly in order to to remove soap deposits or chemicals from new garments which could stick to the iron.

• Your iron is too hot, see our recommendations on temperature control settings in your product manual.
• You are using starch. Only spray starch on the reverse of the fabric to be ironed.

Some laundry starches and synthetic fibres may stick to the surface of the iron. Please clean the Iron's surface.

The internal parts may make metallic noises with the change in temperature. There is nothing wrong with it.

After following the instructions in the user manual for starting the appliance, make sure that your electrical socket is working by plugging another appliance. If it still does not work, do not try to dismantle or repair the appliance yourself, instead, take it to an approved repair centre

Do not use your appliance. To avoid any danger, have it replaced by an approved repair centre.

No, it is normal to have noise and vibration when the steam is activated. The use of steam triggers the functioning of an electric pump.

If the temperature of your iron is adjustable (depending on the model), use steam occasionally when the temperature is set low on the iron.

The temperature is set too low on your iron, it does not allow you to have steam.

Yes, this is quite normal. The water flow allows the cleaning of the soleplate interior.

The self-cleaning operation of the soleplate has to be performed. Refer to the chapter "Maintenance and cleaning", "How to descale my steam generator?".

Yes, this is quite normal. The self-cleaning operation causes the electric pump to operate.

No. The two cables are separately insulated; they are protected and rigorously checked. However, if you notice that the cable is damaged, have it repaired by an approved repair centre.

This system prevents the soleplate from clogging. Its active coating eliminates fibres and impurities that often become stuck to the plate and end up reducing its glide.

Your appliance contains valuable materials which can be recovered or recycled. Leave it at a local civic waste collection point.

Please go to the “Accessories” section of the website to easily find whatever you need for your product.

Find more detailed information in the Warranty section of this website.

If you believe that one part is missing, please call Consumer Services Center and we will help you find a suitable solution.